Power Supplies Copy
Many boats will need two types of batteries, an engine starting battery and a deep cycle battery for powering navigation equipment, lights, domestic equipment, and naturally, your VHF marine radio. Dual types are manufactured but are usually only suited for small powerboats or sailboats.
Furthermore, there are different types of batteries. All will have their pros and cons.
For the purpose of this course and the expected knowledge required for the exam, we will focus on lead-acid (wet-cell) batteries.
The Marine Battery
Looking back, most marine batteries used on boats are of the lead-acid variety. Lead-acid cells consist of a combination of lead and lead peroxide plates. These plates are kept in a solution of sulphuric acid and water (the electrolyte) which produces a potential difference between the plates, and a current can flow when a load, such as a marine radio is connected. During this discharge cycle, the sulphuric acid or the material in the plates is used up. The potential difference no longer exists and the current can no longer flow. This process is reversed by passing a current through the cell in the opposite direction and this is known as ‘charging’.
Battery Construction (courtesy of Battery Council International)
Batteries are made of five basic components:
Each lead-acid cell has a nominal voltage of 2 volts. A physically larger cell does not supply a higher voltage (Volts). Cells in a battery are combined to give a total battery voltage. i.e. three cells to produce a 6 Volt battery or six cells to produce a 12 Volt battery. Each cell will have a filler cap to enable topping up of the electrolyte by distilled or demineralized water. Three filler caps indicate a 6 Volt battery.
Electrical current is measured in amperes (amps). Each lead-acid battery has the capacity to supply an amount of current over a specific time and is known as its Ampere Hour Capacity (AHC). A large cell has the ability to provide a higher AHC over a short period of time or a low current over a longer period of time. Manufacturers will specify the AHC of an individual battery type.
Batteries can be connected to each other, in order to provide a total operating voltage.
SERIES connections, where the negative terminal of one battery is connected to the positive terminal of another battery. i.e. two 6 Volt batteries of equal AHC connected together in order to produce a 12 Volt operating voltage with an AHC of each battery.
2 IN SERIES = Voltage doubles – Amps stay the same
PARALLEL connections, whereby all the positive terminals, of a bank of batteries, are connected together, and all the negative terminals are connected together.
2 IN PARALLEL = Voltage stays the same – Amps double
There are two hazards associated with lead-acid batteries that ship station operators should be aware of:
- the risk of explosion; and
- the risk of chemical burns.
As a result of the chemical process occurring within the cells of a battery during charging, Hydrogen gas is produced. When mixed with air, this can form a highly explosive mixture that can be ignited by a naked flame, a lighted cigarette, or a spark. The spark caused by making or breaking an electrical connection in the vicinity of the charging battery may be sufficient to ignite the hydrogen-air mixture. Batteries should be located as close to the radio equipment as possible and placed in a well-ventilated container or locker. If using metal tools, to work on battery connections, extreme care must be taken to ensure that terminals are not short-circuited.
The electrolyte in battery cells consists of a mixture of water and Sulphuric acid. It is sufficiently concentrated, particularly after charging, to damage eyes, skin, or clothes if spilled or splashed. Immediate and prolonged application of running water is recommended to minimize its effect.
It is recommended that eye protection, gloves, etc be worn when a person is carrying out maintenance on batteries. Batteries should not be topped-up whilst on charge.
Essential Battery Maintenance
The functioning of radio equipment is dependent on the power supplied by the battery. If it is to provide adequate performance in the event of an emergency, regular and careful maintenance is required.
A battery’s service life also depends on the manner in which it is treated. To ensure the best performance from a battery it is important that a battery:
- is kept clean, dry, and free from terminal corrosion;
- has the electrolyte kept at the correct level; and
- is kept correctly charged.
A battery top should be kept clean. A dirty battery top may hold spilled electrolyte on its surface thereby providing a path for the electrical current to leak away. It is important to keep the outside surfaces of a battery dry and free of contamination.
Corrosion forming on terminal clamps may seriously affect, or even prevent, the ability of the battery to supply current. Corrosion will be evident by the formation of a white-green powder between the battery terminals and the terminal clamps. In this situation, the terminal clamp should be removed and both it and the terminal post cleaned.
To minimize the likelihood of corrosion, terminal posts and clamps should be lightly smeared with Vaseline™ or petroleum jelly. A battery that is near flat, defective, or has corrosion of battery terminals may be able to provide sufficient current to operate the receiver, but not the transmitter. Should the transmitter fail to operate and dial lights or channel display dim significantly when the button is operated, the battery should be suspected.
The level of electrolyte inside a battery is important. As a result of the chemical action inside a battery, water is lost. This should be replaced with distilled or demineralized water. Seawater must not be used under any circumstances. The level of the electrolyte should be maintained at approximately 10 mm above the plates unless otherwise specified by the manufacturer. If the electrolyte level is too high, it may overflow during charging providing an unwanted discharge path. If the electrolyte is too low, the plates are exposed to the air and permanent damage and loss of capacity may result.
It may be noticed that a battery that is nearing the end of its useful life will require more frequent topping up than has been previously necessary. Low-maintenance batteries will require infrequent topping-up. Maintenance-free batteries may require none at all.
To provide the best service, a battery must be correctly charged. Both overcharging and undercharging can seriously affect its performance. On small vessels, the usual means of charging the radio battery will be an alternator or generator attached to the vessel’s engine. An associated regulator, which reduces the charging current as necessary, should prevent overcharging.
Vessels that are used frequently (say, several times each week) should have no problem maintaining a fully charged radio battery. However, on vessels that are used relatively infrequently (say, once every few weeks), it is likely that during storage even a battery that starts as fully charged, will self-discharge and go flat.
For safety reasons, it is important that a small boat owner is able to determine the general condition of a battery and its ability to supply current over a period of time (it’s capacity). An indication of the level of charge in a battery may be obtained by either:
- measuring the specific gravity of the electrolyte; or
- measuring the on-load terminal voltage.
Measuring the Specific Gravity
The specific gravity, also called the relative density, of the electrolyte (the liquid inside the battery) varies proportionally with the amount of charge in the battery. It is highest when the battery is fully charged and lowest when the battery is fully discharged or flat. It follows that the amount of charge in a battery can be determined by measuring the specific gravity of the electrolyte. A simple, inexpensive device called a hydrometer is used to measure specific gravity.
In general, for a fully charged battery, the specific gravity should measure about 1.250. A half charge will be indicated by a reading of 1.200 and fully discharged by 1.150. All cells in a battery should indicate a similar specific gravity. A variation of more than about 0.025 will indicate a faulty cell and the battery should be replaced.
Specific gravity readings should not be taken immediately after topping up a cell as the added water will float towards the top of the cell and give a false reading. Charging for thirty minutes or more after topping up will mix the electrolyte and allow accurate readings. Top up the battery before charging as the pouring of cold distilled water onto hot acid in the battery will cause splatter. Batteries that have cells
where specific gravity readings fail to rise or respond poorly to adequate charging, should be replaced.
Measuring the On-Load Terminal Voltage
Measurement of the terminal voltage when a battery is supplying current to a load, such as a transmitting radio, will also provide an indication of the amount of charge in a battery. This measurement is known as the on-load terminal voltage.
For a 12-volt battery, the on-load terminal voltage should not fall below approximately 11.4 volts while transmitting. If the voltage does fall significantly below this figure, the battery requires charging.
If after charging, the on-load terminal voltage still falls significantly below 11.4 volts, it is an indication of a faulty cell and the battery should be replaced.
Measurement of the off-load (when the battery is idle) terminal voltage of a battery is a poor indicator of its condition.
Loss of Capacity
A battery will suffer a gradual loss of capacity during its life. This is inevitable and the battery should be replaced when the capacity loss becomes significant. Many lead-acid batteries have a commercial life of only two to three years. However, the useful life of a battery can be considerably shortened by:
- operating a battery in a low state of charge for long periods;
- allowing a battery to stand in a discharged state for long periods;
- leaving a charged battery for long periods without periodic charging; and
Battery isolation switch
These are familiar to most boaters as a large, usually red switch with a round face and prominent knob. It is the go-to switch in case of an electrical fire. Disconnecting your power supply can prevent further damage to your equipment in case of fire or fludding.
Maintenance Free Batteries
Maintenance-free Lead – Acid or Gel type batteries are becoming increasingly more popular and available to mariners. Users of these types of batteries are recommended to follow the manufacturer’s guidelines in ascertaining the condition of the battery regarding a replacement. On vessels where it is mandatory to carry an independent emergency means of electrical supply, for communications equipment, it may also be a requirement to replace ‘maintenance free’ batteries after a short operational period of 1 year.
Connection of batteries during emergencies
For a vessel with more than a single bank of batteries, it is highly recommended to connect the batteries in parallel during emergency situations. The battery on/off or interchange switch will indicate if this is possible.